The article author is making several great points related to How to Install a Bathtub Yourself overall in the article down the page.
Installing a bath tub isn't specifically rocket science, however it does need solid plumbing, woodworking, and also sometimes, tiling skills. Replacing an old bath tub with a new one is likewise a reasonably challenging job. If the old bathtub is conveniently available, the job can relocate speedily; if you have to open a wall to eliminate the old tub as well as position the new bathtub, the task is much harder. In either case, the project is within a residence handyman's abilities, although you will certainly require an assistant to move out the old bathtub and also embeded in the brand-new one. Make sure you have actually certified yourself for the job and are comfortable attempting it. Rather than working with a service provider to take over a halfway-completed project, it is much better to think about using one prior to you begin. Chances are you might require an expert plumber to make tube connections.
This short article will certainly help you mount a brand-new tub in your shower room if you have actually already bought a brand-new bathtub and don't need to change the setup of your previous water system pipelines.
Your tools and product checklist ought to make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you should do is detach the water system. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The process of eliminating the existing taps can be fairly troublesome due to the restricted gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the faucets. Have a towel all set for the remaining water that will certainly come from the pipes. When the supply pipes have actually been gotten rid of, make use of the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the single faucets from transforming throughout this procedure. When the faucets have actually been removed, the holes in the bath/basin will certainly have to be cleaned up of any type of old sealing compound.
Prior to moving on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, then a shank adapter is needed for the brand-new taps to fit.
Fitting New Touches
If the tails of the brand-new taps are plastic, after that you will require a plastic port to stop damage to the string. One end of the connector fits on the plastic tail of the tap and also the other end gives a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will need lowering couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the faucet and also the sink. Protect the faucet in position with the manufacturer offered backnut. As soon as the faucet is safely in place, the supply pipelines can be attached to the tails of the taps. The taps can either be attached by utilizing corrugated copper piping or with normal faucet ports. The previous kind should be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Mounting the Bath tub
Using the two wood boards under its feet, put the bathtub in the required position. The wood boards are valuable in uniformly spreading the weight of the tub over the location of the boards instead of focusing all the weight onto 4 little factors.
The next goal is to make certain that the bathtub is leveled all round. This can be achieved by inspecting the spirit level as well as adjusting the feet on the bath tub till the spirit level reads level.
To install taps, fit all-time low of the outermost flexible faucet port to the proper supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Switch on the water as well as examine all joints and new pipework for leaks and tighten them if required. Load the tub as well as additionally check the overflow electrical outlet and also the regular electrical outlet for leakages.
Lastly, fix the bath paneling as defined in the supplier's user's manual. Tiling and securing around the tub ought to wait until the bathtub has been made use of at the very least when as this will certainly settle it into its last position.
Preparing for the Setup
To start with, the sustaining structure supplied with the bathroom needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the tub. When suitable the tap block, it is essential to ensure that if the tap features a plastic washing machine, it is fitted in between the bathroom and the taps. On a plastic bath, it is also practical to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (sometimes supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the supplied washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a similar manner.The bath must currently prepare to be fitted in its last position.
Tiling Around the Bath tub
In the area where the bathroom satisfies the tile, it is needed to secure the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a rigid seal, triggering the water to penetrate the wall surface between the bath and also the tiling, leading to problems with dampness as well as feasible leakages to the ceiling listed below.
You can select from a range of coloured sealers to assimilate your fixtures as well as installations. They are offered in tubes and cartridges, as well as are capable of securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can load it with spins of soaked paper or soft rope. Keep in mind to always fill the bathtub with water prior to securing, to enable the motion experienced when the bathtub remains in usage. The sealant can crack fairly early if you do not consider this motion prior to securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to size, are additionally conveniently offered on the marketplace. It is a good idea to fit the floor tiles using water-resistant or water-proof adhesive and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We had been brought to that write-up on How to Install a Bathtub from someone on another web page. Don't hesitate to take a moment to share this blog posting if you enjoyed reading it. I praise you for your time. Visit again soon.
Click Here!